24/7 SUPPORT

+91 9495912681


Today's Deals: Great Savings

Hand-picked deals with low prices

Offer Ends In

Chainsaw Carburetor for Powertex sunflower etc...

1,143.74 970.00

Check Delivery At //

You must be logged in to access this page
Sold By jselectricals
Report Abuse
SKU chainsaw-carburetor-for-powertex-sunflower-etc Categories , Tag
Material Cast Steel
Usage In Chainsaw Engine
Surface Treatment Galvanized

With vast industrial experience, we are involved in offering a wide range of Chainsaw Carburetor.

Description
Material Cast Steel
Usage In Chainsaw Engine
Surface Treatment Galvanized

The carburetor on a chain saw is pretty simple, as carbs go, but it’s not entirely uncomplicated. The job of the carb is to accurately meter extremely tiny quantities of fuel and mix it with the air entering the engine so that the engine runs properly.

If there is not enough fuel mixed with the air, the engine “runs lean” and either will not run or potentially gets damaged (in a two-stroke engine, the fuel also supplies the engine’s lubricant). If there is too much fuel mixed with the air, the engine “runs rich” and either will not run (it floods), runs with a lot of smoke, runs poorly (bogs down, stalls easily) or, at the very least, wastes fuel. The Carburetor is in charge of getting the mixture just right.

The Carburetor on a chain saw is simpler than most carbs because it really has only three situations that it has to cover:

  • It has to work when you are trying to start the engine cold.
  • It has to work when the engine is idling.
  • It has to work when the engine is wide open.

No one operating a chain saw is really interested in any gradations between idle and full throttle, so incremental performance between these two extremes is not very important. In a car, the many gradations are important, and this is why a car’s Carburetor is a lot more complex.

You can see the Carburetor for the chain saw in the following two photos:

Chainsaw Carburetor
Photo 2: This is the side that receives the outside air through the air filter.

Here are the parts of a Carburetor :

  • A carburetor is essentially a tube.
  • There is an adjustable plate across the tube called the throttle plate, which controls how much air can flow through the tube. You can see this circular brass plate in photo 1 above.
  • At some point in the tube there is a narrowing, called the venturi, and in this narrowing a vacuum is created. The venturi is visible in photo 2.
  • In this narrowing there is a hole, called a jet, that lets the vacuum draw in fuel. You can see the jet on the left side of the venturi in photo 2.

Watch the video for a better look at these parts.

The Carburetor is operating “normally” at full throttle. In this case, the throttle plate is parallel to the length of the tube, allowing maximum air to flow through the Carburetor . The air flow creates a nice vacuum in the venturi, and this vacuum draws in a metered amount of fuel through the jet. You can see a pair of screws on the top-right of the Carburetor in photo 1. One of these screws (labeled “Hi” on the case of the chain saw) controls how much fuel flows into the venturi at full throttle.

When the engine is idling, the throttle plate is nearly closed (the position of the throttle plate in the photos is the idle position). There is not really enough air flowing through the venturi to create a vacuum. However, on the back side of the throttle plate there is a lot of vacuum (because the throttle plate is restricting the airflow). If a tiny hole is drilled into the side of the Carburetor tube, fuel can be drawn into the tube by the throttle vacuum. This tiny hole is called the idle jet. The other screw of the pair seen in photo 1 is labeled “Lo” and controls the amount of fuel that flows through the idle jet.

When the engine is cold and you try to start it with the pull-cord, the engine is running at an extremely low rpm. It is also cold, so it needs a very rich mixture to start. This is where the choke plate comes in.

When activated, the choke plate completely covers the venturi (watch this video of the choke plate to see it in action). If the throttle is wide open and the venturi is covered, the engine’s vacuum draws a lot of fuel through the main jet and the idle jet. Usually, this very rich mixture will allow the engine to fire once or twice, or to run very slowly. If you then open the choke plate, the engine will start running normally.

Reviews (0)

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Questions and Answers

Questions and Answers

You are not logged in

More Offers
Sorry no more offers available
Shop
0 Wishlist
0 items Cart

Check Delivery At //

Shopping cart

close

Sign in

close

OR

Scroll To Top